Spaulding-lighting Laredo LLC Bedienungsanleitung PDF herunterladen

INSTALLATION INSTRUCTIONS

LAREDO LLC LUMINAIRE

STEP-I MOUNTING PREPARATION

* Drill wall for the hardware appropriate for

* Using template (page 4) lay over junction box (A)

on the wall. Mark at (3) hole.

the type of wall. Use 1/4" diameter bolts (not provided).

* Pull the supply wires (B) from junction box (A).

STEP-II FIXTURE MOUNTING PREPARATION

* To open door (C), loosen (2) retaining screws (D).

* Loosen (4) screws (E) then gently lower reflector (F).

STEP-IV WIRING

POWER MUST BE OFF.

(WIRING MUST BE PERFORMED

BY A QUALIFIED ELECTRICIAN)

* Wire service leads to fixture power leads

according to local and National Elec. Codes.

* For direct wire connections, connect

wire back to J-box on the wall. Connect

black to black and white to neutral then

push connections back inside J-box (A).

* Apply caulking sealant around the

top and both sides of the housing.

* Tighten bolts securely.

* Hang fixture on the mounting hardware

at the wall thru key-slots opening (J).

* Insert all wires (B) thru opening

at the back of housing.

STEP-III FIXTURE MOUNTING

(Fig. 6)

ground wire to green wire then push

(Fig. 1)

Hubbell Lighting, Inc. Doc. Number: 93015030

A subsidiary of Hubbell Incorporated Revision: *

701 Millennium Blvd • Greenville, SC 29607

Phone: (864) 678-1000

FIG. 5

FIG. 3

(Fig. 6)

(Fig. 8)

(Fig. 2)

(Fig. 4)

SEE PAGE 4

FULL SIZE

TEMPLATE

READ ALL INSTRUCTIONS CONTAINED HEREIN BEFORE PROCEEDING WITH INSTALLATION OF FIXTURE.

WARNINGS:

- HUBBELL LIGHTING WILL NOT WARRANTY ANY FIXTURES FOR ANY REASON IF THE INSTALLER OF THE

FIXTURE DOES NOT READ AND COMPLY WITH ALL OF THE INSTRUCTIONS CONTAINED HEREIN.

- DISCONNECT POWER BEFORE INSTALLATION OR SERVICING.

- INSTALL, OPERATE AND MAINTAIN TO MEET ALL APPLICABLE CODES.

- ALL SERVICING OR RELAMPING MUST BE PERFORMED BY QUALIFIED SERVICE PERSONNEL.

- ALL CONNECTIONS SHOULD BE CAPPED WITH SUITABLE INSULATED WIRE CONNECTORS (BY OTHERS).

- LAMP AND BALLAST MUST BE EQUAL ANSI CODE AND WATTAGE.

- THIS LUMINAIRE IS APPROVE ONLY FOR WALL MOUNT AND DOWNWARD ORIENTATION IN WET LOCATION.

1.00 REF.

4.56 REF.

5.00 REF.

MARK AT

CENTER

ALIGN WITH TOP EDGE

OF JUNCTION BOX

FIG. 1

* For optional quick release door latch,

push pin to open door.

* Lossen screws (G), remove cover (H).

(Fig. 3)

(Fig. 5)

FIG. 4

FIG. 2

PUSH PIN

PAGE 1 OF 8

PAGE 1 DE 8

PAGINA 1 DE 8

1 2 3 4 5 6 7 8

Inhaltsverzeichnis

Seite 1 - LAREDO LLC LUMINAIRE

INSTALLATION INSTRUCTIONSLAREDO LLC LUMINAIRESTEP-I MOUNTING PREPARATION* Drill wall for the hardware appropriate for* Using template (page 4) lay ove

Seite 2

STEP-V LAMPING* Replace reflector (F).* Engage the lamp to socket (S). * To ensure proper contact, loosen the lamp one turn then retighten.METAL HAL

Seite 3 - ACCESSORIES INSTRUCTIONS

ACCESSORIES INSTRUCTIONSLAREDO LLC LUMINAIREWARNING: DISCONNECT POWER BEFORE INSTALLATION OR MAINTENANCEREAD INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING

Seite 4

Hubbell Lighting, Inc. Doc. Number: 930

Seite 5 - LUMINAIRE LAREDO LLC

Hubbell Lighting, Inc.

Seite 6 - 93015030

Hubbell Lighting, Inc.

Seite 7

Hubbell Lighting, Inc.

Seite 8 - EQUIPAMIENTO INSTRUCCIONES

Hubbell Lighting, Inc.

Kommentare zu diesen Handbüchern

Keine Kommentare

Spaulding-lighting Laredo LLC Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Beleuchtung Spaulding-lighting Laredo LLC herunter. Spaulding Lighting Laredo LLC User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Beleuchtung Spaulding-lighting Laredo LLC